Velleman-projects K5201 Assembly instructions Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Velleman-projects K5201 Assembly instructions herunter. Velleman projects K5201 Assembly instructions User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 16
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
LIGHT COMPUTER
K5201
ILLUSTRATED ASSEMBLY MANUAL H5201IP-1
Total solder points: 240
Difficulty level: beginner 1 2 3 4 5 advanced
1
6
d
i
f
f
e
r
e
n
t
p
a
t
t
e
r
n
s
a
n
d
7
o
u
t
p
u
t
s
p
r
o
v
i
d
e
a
u
n
i
q
u
e
l
i
g
h
t
s
h
o
w
.
Seitenansicht 0
1 2 3 4 5 6 ... 15 16

Inhaltsverzeichnis

Seite 1 - LIGHT COMPUTER

LIGHT COMPUTER K5201 ILLUSTRATED ASSEMBLY MANUAL H5201IP-1 Total solder points: 240 Difficulty level: beginner 1  2  3  4  5  advanced 16

Seite 2

10 Cascading of two units : Two units can be hooked-up in cascade configuration, to create a 14 -channel lightshow. Hook-up both units as shown in t

Seite 3 - Assembly hints

11 Do not use a single transformer for both units. Make sure the ‘L’ (live) of both kits is connected to the same phase of the mains. Not doing s

Seite 4

12 When mounting the kit in an enclosure you should make sure the enclosure is sufficiently insulated according to local norms. The complete PCB

Seite 5 - 1/4W Resistors

13 19. Schematic diagram. Schematic diagram

Seite 6 - 0.9"

14 PCB 20. PCB

Seite 7 - 16. Rotary switch

VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com

Seite 8

5 410329 289348Modifications and typographical errors reserved - © Velleman nv, Legen Heirweg 33 - 9890 Gavere (België) H5201IP - 2011 - ED1_rev.1 Le

Seite 9 - FIG. 1.0

2 Features: Sixteen different patterns and 7 outputs provide a unique light show Easy pattern selection with rotary switch Adjustable effect sp

Seite 10 - FIG. 2.0

3 Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project su

Seite 11

DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST! REMOVE THEM FROM THE TAPE ONE AT A TIME !

Seite 12 - 18. FINISHING

5 Construction R1 : 4K7 (4 - 7 - 2 - B) R2 : 39K (3 - 9 - 3 - B) R3 : 10K (1 - 0 - 3 - B) R4 : 10K (1 - 0 - 3 - B) R5

Seite 13 - 19. Schematic diagram

6 Construction 7. PCB tabs. RV1 : 1M 6. Trimmer SW1 11. Push button 12. LEDs. Watch the polarity! LD. ..CA T H O DE23mm0.9"23mm

Seite 14 - 20. PCB

7 IC1 : NE555 IC2 : CD4024 IC3 : VK5201 (programmed Eeprom 2764C25) 15. ICs. Watch the position of the notch! SW 2 : 1p 14.

Seite 15

8 All wires of the output section must be at least 2.5mm². Power supply wiring can be done with 0.5mm² wire. Use fuse ratings as indicat

Seite 16 - SOLDERLESS

9 Hook-up of one unit : Hook-up the unit as shown in the diagram 1.0. To use the internal speed adjustment, connect ‘OSC OUT’

Kommentare zu diesen Handbüchern

Keine Kommentare